ASME B18.2.3.2M-2005 Metric Formed Hex Screws
|
ID： |
6B69F32F61BA428B967C0775862B7849 |
|
文件大小(MB)： |
0.24 |
|
页数： |
22 |
|
文件格式： |
|
|
日期： |
2010-8-22 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
A N A M E R I C A N N A T I O N A L S T A N D A R D,Metric Formed,Hex Screws,ASME B18.2.3.2M-2005,[Revision of ASME B18.2.3.2M-1979 (R1995)],ASME B18.2.3.2M-2005,[Revision of ASME B18.2.3.2M-1979 (R1995)],Screw, Cap, Formed Hex Head -,Metric Formed,Hex Screws,Three Park Avenue ?New York, NY 10016,AN AMERICAN NATIONAL STANDARD,Date of Issuance: September 14, 2005,This Standard will be revised when the Society approves the issuance of a new edition. There will be,no addenda issued to this edition.,ASME issues written replies to inquiries concerning interpretations of technical aspects of this Standard.,Interpretations are published on the ASME Web site under the Committee Pages at,http://www.asme.org/codes/ as they are issued.,ASME is the registered trademark of The American Society of Mechanical Engineers.,This code or standard was developed under procedures accredited as meeting the criteria for American National Standards.,The Standards Committee that approved the code or standard was balanced to assure that individuals from competent,and concerned interests have had an opportunity to participate. The proposed code or standard was made available,for public review and comment that provides an opportunity for additional public input from industry, academia,regulatory agencies, and the public-at-large.,ASME does not “approve,” “rate,” or “endorse” any item, construction, proprietary device, or activity.,ASME does not take any position with respect to the validity of any patent rights asserted in connection with any items,mentioned in this document, and does not undertake to insure anyone utilizing a standard against liability for infringement,of any applicable letters patent, nor assumes any such liability. Users of a code or standard are expressly advised,that determination of the validity of any such patent rights, and the risk of infringement of such rights, is entirely their,own responsibility.,Participation by federal agency representative(s) or person(s) affiliated with industry is not to be interpreted as government,or industry endorsement of this code or standard.,ASME accepts responsibility for only those interpretations of this document issued in accordance with the established,ASME procedures and policies, which precludes the issuance of interpretations by individuals.,No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.,The American Society of Mechanical Engineers,Three Park Avenue, New York, NY 10016-5990,Copyright . 2005 by,THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS,All rights reserved,Printed in U.S.A.,CONTENTS,Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv,Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v,Correspondence With the B18 Committee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi,1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Comparison With ISO Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,3 Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,4 Referenced Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,6 General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,Figures,1 Formed Hex Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,2 Fillet Details For Short Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,3 Fillet Details For Long Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,A1 Typical Straightness Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9,B1 Typical Gage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,Tables,1 Dimensions of Formed Hex Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,2 Tolerance Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ……
……